Commercially pureFormability to higher CP strength
General corrosion service and fabrication, with strength increasing from Grade 1 through Grade 4.
Titanium mill products and drawing-led supply
Titanium bar, plate, tube and forgings,
specified for the order.
Beiyu is a China-based titanium supplier supporting overseas industrial RFQs. We review bar, plate, sheet, tube, forgings, wire, billet and drawing-led components against the grade, governing standard, dimensions, inspection scope and release documents stated in the enquiry.
ASTM and AMS routes
EN 10204 by order
Drawing-led supply
Commercial coordination: Jiaxing · Technical supply coordination: Baoji · Responsible mill or fabricator and process route confirmed in the quotation. Representative footage.
Quotation basisWhat the quotation confirms
Product basisForm, dimensions, condition and quantity
Material identityGrade, standard, revision and heat or lot
Acceptance scopeMethod, criteria and inspection points
Release packageMTC, marking, reports and packing records
Start with the product form
The ordered form determines the governing specification, dimensional basis and practical supply route. These six routes cover most industrial titanium enquiries.
ASTM B348 · AMS 4928
Titanium bar and rod
Grade, section, length, condition and tolerance define the ordered stock.
View product
ASTM B338 · B861 · B862
Titanium tube and pipe
Service, OD, wall thickness, length and test scope determine the route.
View product
ASTM B265
Titanium sheet and plate
Thickness, width, length, condition and tolerance define flat-product supply.
View product
ASTM B381Titanium forgingsRings, discs, blocks and drawing-led preforms
ASTM B863Titanium wireCoiled, spooled or straight supply
Primary stockTitanium billetFeedstock for forging, rolling or machining
More titanium and drawing-led supplySpecialist materials, equipment and components View routes
Strip and foilThin-gauge and coil supply
Titanium anodesElectrochemical service
Porous titaniumFiltration and flow control
Clad titaniumCorrosion-resistant assemblies
Chemical equipmentVessels, piping and exchangers
Machined partsDrawing-led CNC components
Pumps and valvesTitanium wetted components
Fittings and accessoriesFlanges, fasteners and custom parts
Select material and standard together
An alloy name alone is not a purchasing specification. Begin with material behavior, then match the grade to the standard governing the ordered product form.
Titanium grade families
Strength and medicalAlloyed and low-interstitial routes
Higher-strength bar, plate, forgings, tube and drawing-led components when specifically ordered.
Corrosion servicePalladium-bearing and Ti-Ni-Mo routes
Selected against the actual corrosion environment; not automatic substitutes for Grade 2.
Standards and buyer inputs by product form
The standard sets the route; the RFQ still needs the dimensions, condition, quantity and document scope that control quotation.
Product routeCommon referencesBuyer detailsDocument notes
Sheet, plate and stripASTM B265 · ASME SB-265 · AMS 4911Thickness, width, length, condition and toleranceMTC and flat-product results by order
Bar and billetASTM B348 · AMS 4928Diameter or section, length, straightness and conditionHeat identity and mechanical results
Tube and pipeASTM B338 · B861 · B862OD, wall, length, route and test scopeNDT and pressure testing when specified
Forgings and fittingsASTM B381 · ASTM B363Drawing, allowance, condition and heat treatmentUT, PT or witnessed testing by order
Wire and welding wireASTM B863 · AWS A5.16Grade, diameter, condition and packagingLot identity and certificate scope
Inspection documentsEN 10204 3.1 · 3.2 when orderedValidation level, method and acceptance criteriaConnect records to the delivered heat or lot
Additional material familiesNickel, zirconium, refractory and clad routesView materials
Define the selection basis before choosing a grade
An industry label is only a starting point. Begin with the operating environment or governing document, then confirm the product form, standard, acceptance and traceability scope.
Chemical processing
Corrosion and heat-transfer duties begin with the actual fluid and operating conditions.
- Confirm
- Medium, concentration, temperature and pressure
- Then define
- Equipment duty and ordered product form
Marine and desalination
Seawater and heat-transfer duties begin with water chemistry and the operating envelope.
- Confirm
- Water chemistry, temperature, pressure and flow
- Then define
- Tube, sheet, fitting or fastener requirement
Aerospace components
Controlled component enquiries begin with the drawing revision, specification and product route.
- Confirm
- Drawing revision, specification and material condition
- Then define
- Allowance, inspection and traceability scope
Medical-related material
Medical-related enquiries begin with the governing specification and ordered product form.
- Confirm
- Governing specification and ordered product form
- Then define
- Surface condition and lot traceability
Metal additive manufacturing
Drawing-led additive parts begin with the alloy, build route and required post-processing.
- Confirm
- Alloy, build process and drawing revision
- Then define
- Allowance, critical dimensions and validation
Industrial OEM machining
Equipment-builder enquiries begin with the drawing, stock route and machining allowance.
- Confirm
- Drawing revision, alloy and starting product form
- Then define
- Allowance, tolerances and inspection points
External photographs establish application context only. They are not Beiyu project evidence and do not establish a titanium grade, product route or qualification.
Photography credits
Chemical processing · Desalination: Blueye, CC BY-SA 3.0 · Aerospace: NASA · Medical: Peter Kasprzyk, CC0 · Additive manufacturing: NIST · OEM machining: Beiyu supply-network photograph
Evidence must connect to the delivered material
Inspection is useful only when the method, acceptance basis and resulting records are linked to the supplied heat, lot or item.
TC4 tensile test report
Room-temperature tensile testing for a submitted TC4 sample, including tensile strength, proof strength and elongation.
- Issuer
- Hantang Test · Baoji
- Criterion
- GB/T 3621-2022
- Method
- GB/T 228.1-2021
- Report
- B25WT089293
Representative third-party reports
Select a record to inspect the source scan and its stated method.
Define the release package before production
“Standard certification” is not a complete requirement. Name the document, validation level, method and traceability connection in the order.
Grade, product standard and revision, plus heat or lot identity.
Material + MTCRequired EN 10204 type and the chemical or mechanical results to report.
3.1 or 3.2PMI, UT, PT, dimensions or witnessed tests with method and acceptance criteria.
Method + criteriaMarking, packing list and reports linked to the delivered material.
Traceable packageEN 10204 3.2 and third-party witnessing are included only when ordered.
Add document scope to RFQTitanium standards and purchasing guides
Use these references to compare titanium grades, ASTM and AMS product standards, RFQ inputs, and MTC or EN 10204 document scope before quotation.
Questions that define a usable RFQ
These answers cover the information most often needed before material, inspection and release scope can be compared.
Which details should be sent before quotation?
State the product form, grade, governing standard and revision, dimensions, tolerance, surface condition, quantity, destination and required document package. Add the required date when schedule affects the supply route.
Can Beiyu quote drawing-based components?
Yes. Send PDF, STEP or CAD files with the drawing revision, material grade, critical dimensions, machining allowance, inspection points and quantity. Manufacturing and inspection scope are confirmed in the quotation.
What document scope should be stated?
State the required MTC or EN 10204 type, heat or lot traceability, and any PMI, UT, PT, dimensional reporting, witnessed testing or third-party inspection requirements before production.
Is there a fixed minimum order quantity?
The practical minimum depends on product form, grade, dimensions and the responsible supply route. Send the target quantity; any production-lot or minimum-order constraint is stated in the quotation.
When is the delivery schedule confirmed?
Lead time is confirmed after the material route, dimensions, quantity, required testing and document package are reviewed together. The agreed schedule is recorded in the quotation.
Does a sample report certify my order?
No. A sample report applies only to its identified submitted sample. The RFQ and purchase order must define the inspection certificate and reports connected to the delivered heat, lot or item.
Ready for technical review
Send what you know. We will identify what is missing.
Product, grade, dimensions or a drawing are enough to start. A complete specification is not required for the first enquiry.